2150cc FIC Mitsubishi DSM or EVO 8/9 Fuel Injector Clinic Injector Set (High-Z)

  • $914.00
Qty:  
OR
  • Shipping Policy

    World Wide Shipping Available

  • Payment methods

    Paypal Account Not Required for Checkout

    Paypal-all-credit-cards_mpji7j.png



Mitsubishi DSM/Evo Fuel Injector Clinic Injector Set: 4 x 2150cc Saturated / High Impedance Injectors. Largest high impedance injector ever! Utilizing the latest injector technology and featuring state of the art matching with Data Match Technology . Great injector for E85 applications! These injectors do not require a resistor pack or P&H drivers. Includes pigtails PGT DEN4 or add Plug & Play adaptors PADPDtoJ4. DO NOT USE WITH VP Import, Q16 or OTHER MTBE OXYGENATED FUELS. Resistor pack removal recommended.


This massive injector is in a class of its own when low end throttle response and short pulse width control is required. State of the art Data Match Technology dynamic flow matching is used during the production of these injector sets due their large flow rate. This significantly improves the ECUs ability to control these injectors in the sub 2ms pulse width area, typical of idle and part throttle conditions.

Each injector is individually serial numbered and the results are provided on the Data Match Sheet providing the most complete flow matching and latency value information available in the industry today.


Fuel Injector Clinic injectors are flow tested and rated at 43.5psi (3Bar) at 90ºF fuel temperature using CF-16B calibration fluid.


CAUTION! The internal construction of this 2150cc/min injector includes a seal that has been found to swell when in contact with MTBE from oxygenated fuels like Q16 or VP Import. This swelling causes a significant reduction in flow through the injector and therefore renders it unsuitable for use with MTBE oxygenated fuels. Please be sure to follow the care instructions for these injectors since there are potential corrosion issues that may arise from prolonged disuse while exposed to alcohol based fuels (E85, etc.)


Fuel Injector Clinic injectors are set up to and include all o-rings needed to fit the factory application for the listed vehicle. For aftermarket or other unusual setups please contact us prior to placing your order to make sure you receive injectors that fit properly.


Every injector is covered against failure caused by defects in original manufacture by our 12 month warranty.


This injector set contains high impedance injectors matched to the saturated injector signal generated by this vehicles OEM ECU, OR is suitable for use with an aftermarket ECU made or set up for high impedance injectors.


This set of injectors requires you to change the injector plug on the wiring harness in your car. This can be done by soldering in the pigtails (included with purchase) to replace the plugs currently on your harness, or you can choose to purchase the optional plug-n-play adaptors which will convert from the type of plugs on these injectors to the plugs on your harness without any need for cutting or soldering.


This plug conversion is made necessary because FIC always chooses to provide brand new, unused injectors for its performance applications. We do not believe that increasing the chance of a failure due to using remanufactured or core program based injectors is ever warranted.


HP Rating


Cylinder Quantity4

ImpedanceHigh-Z

WHP on Gas at 43.5psi 90%DC Turbo1044

WHP on Gas at 58psi 90%DC Turbo1206.15

WHP on E85 at 43.5psi 90%DC Turbo803

WHP on E85 at 58psi 90%DC Turbo928

WHP on Gas at 43.5psi 90%DC NA1253

WHP on Gas at 58psi 90%DC NA1447

WHP on E85 at 43.5psi 90%DC NA964

Fuel Pressure (psi)43.5

Engine aspirationturbocharged

Adaptors


Plug-N-Play AdapterPADPDtoJ4


    • SKU
      IS126-2150H
  • Plus & Play Option:
    Plug & Play Adapter, Solder-in Pigtails
  • Resistor Pack Delete:
    No Resistor Pack Delete Plug, Resistor Pack Delete Plug

AF Shipping Policy

DOMESTIC SHIPPING (Orders within the USA)

All orders are shipped using UPS, FEDEX, or USPS using their Current Shipping Rates and includes Insurance up to $999 for Manifold orders using UPS/FEDEX and $100 for USPS Flat Rate. Please contact us if you need additional Shipping Insurance before ordering.

USPS (United States Postal Service)

Selecting the USPS 3-5 day express option is for Domestic Customers ordering small sized products that would fit in a Small/Medium/Large Flat Rate Box. If you are ordering from a country OUTSIDE THE USA, additional Fees Could Apply from selecting this option.

INTERNATIONAL SHIPMENTS:

We do offer world wide shipping, Via UPS, DHL, or USPS. However, our website is not currently configured to accurately quote international shipments. Please contact us Prior to Ordering for an accurate quote if you are from outside the USA.

CUSTOMS, DUTIES, & IMPORT FEES:

Customers are responsible for all Customs, Duties, and Import Fees associated with international shipments between you and your Local or Federal Government. We will NOT falsely lower the Declared Value to help avoid or lower your Import Fees

CUSTOMERS SHIPPING ITEMS TO ARCHER FAB

Customers shipping items to Archer Fab that are needed for the Fabrication process (Turbocharger, or Turbine housing) will be charged the Return Shipping, additional to the amount originally paid in the invoice, unless otherwise specified or included.



We accept the following payment methods:

AF Consumer Terms & Conditions / Warranty Info
By purchasing from Archer fabrications LLC, you the consumer Understand and Agree to the following:
• All Archer fabrications, LLC. Products are intended for off road/track use only, and are recommended to be installed by a professional.
• All Archer Fabrications, LLC. Hand Made, Welded, & Fabricated Parts are Final sale (no refunds); Including but not necessarily limited to: Turbo manifolds, exhaust systems, waste gate dump tubes, O2 housings etc... 

•Returns: 

It is SOLELY at the discretion of Archer Fabrications, LLC.  to Approve or deny any AF welded product returns. Any and all approved returns will be subject to a 50% Restocking fee based off the total invoice

•All Third party products that are Returned/Refunded will be subject to the manufacturers return/exchange policy and a 25% Restocking fee.


• All Archer Fabrications, LLC Turbo Manifolds will include a LIMITED 3 YEAR WARRANTY Against welding related defects to the original purchase only, from the date purchased. Please contact us if you have any issues with your product and we will do our best to make it right.

• The limited warranty does not cover damage you may have caused & related or due to the following:

•User neglect, improper installation, damage related to a heavy Waste gate dump tube, damage due to vibratory contact from other parts, Damage caused from "heat wrapping".


Archer Fabrications, LLC. Will not be held liable for any damage that could occur to the related and moving parts associated with a turbo system, such as; The Engine & The Turbocharger, or damage to the vehicle itself, at anytime.


Archer Fabrications, LLC. Reserves the right to change or update the Terms and conditions / Warranty Info at any time.

Customers who bought this product also bought

Customers who viewed this product bought